- App ：VpnCilla
- 版本 ：3.3.1
- 系统 ：4.1 及更高版本
- 提供者 ：Matthias Meier
- 开发者 ：[email protected]
VpnCilla介绍 ：
Before you buy this software, please test with the free "VpnCilla (Trial)" (also available at the google play market)!
VpnCilla is a VPN Client for VPN Servers as FritzBox, Cisco PIX/ASA, Fortigate or other VPN Servers with IPSec Pre-shared Keying (Xauth IKE/PSK).
Features:
* Profile automatically taken from the Trial version (don't uninstall the Trial until the first run of this full version)
* No root access needed (if the device fully conforms to Android 4)
* Compatible with Fritzbox, Cisco PIX/ASA, Fortigate VPN Servers and others (?)
* Connects/Disconnects with a single click (by a Shortcut-Widget)
* Automatic Reconnect Mode on WiFi/Mobile failover/outage
* Supports Multiple Profiles
* Supports automatic Cisco Split Routing
* Passwords may be stored in profile or always manually entered when connecting (which is much more safe)
Advanced Settings:
* Possibility to specify WiFi Blacklists/Whitelists to explicitely deny/allow VPN on only specific WiFi ESSDs
* Possiblity to specify Manual Routes and/or DNS Server and much more…
Restrictions:
– Mention the security risk if passwords are stored in profile in case your device will be hacked or stolen!
– VpnCilla runs only if the TUN driver (tun.ko) as well as the the Android 4 VPN routing infrastructure is included in the firmware. UNFORTUNATELY NOT ALL DEVICE MANUFACTURER YET HAS INCLUDED IT!! Check with "VpnCilla (Trial)" first!
– Only IKE/PSK Xauth authentication is supported (no PPTP, no L2TP, no Hybrid RSA, no SSL, no Cisco AnyConnect, …)
– supports IPv4 only (no IPv6)
– supports WLAN/WIFI as well as Mobile Data up to 3g. VpnCilla is unstable over 4g (LTE) on some devices / with mobile providers
– Active Screenfilter apps as Twilight or Lux might prevent selecting of the security dialog checkbox
– VpnCilla can't handle phase 1 rekeying initiated by the VPN server. On Fritzboxes this will occure after 1h connection time whereas on Cisco VPN servers the rekeying interval is configurable and by default after 8h. Typically the session stalls for 2-3 minutes until VpnCilla initiates a reconnect.在您购买此软件，请与自由“VpnCilla（试行）”（也可在谷歌发挥市场）测试！
VpnCilla是VPN客户端的VPN服务器作为FritzBox，思科PIX / ASA，飞塔或使用IPSec预共享键控（扩展验证IKE / PSK）其他VPN服务器。
产品特点：
*简介自动从试用版（不要卸载该试用直到这个完整版的第一次运行）
*没有root访问权限需要（如果该设备完全符合了Android 4.0）
*兼容Fritzbox，思科PIX / ASA，飞塔VPN服务器和其他人（？）
*只需点击一下连接/断开（通过快捷方式，窗口小部件）
*自动重新连接模式上的WiFi /手机故障切换/故障
*支持多个配置文件
*支持自动思科路由分割
*密码可以存储在配置文件或连接时总是手动输入（这是更安全）
高级设置：
*可以指定无线黑名单/白名单，以明确地拒绝/允许VPN上只有特定的WiFi静电敏感器件
*方法可行手动指定路线及/或DNS服务器等等…
限制：
– 请指出密码存储在配置文件的情况下，您的设备将被黑客入侵或被盗的安全隐患！
– VpnCilla运行仅当TUN驱动程序（tun.ko），以及在Android的4 VPN的路由基础设施包括在固件。很不幸，不是所有的设备制造商尚未包括了IT！请与“VpnCilla（试行）”第一个！
– 仅支持IKE / PSK XAuth认证（无PPTP，L2TP没有，没有混合的RSA，无SSL，没有思科的AnyConnect，…）
– 支持IPv4只（没有IPv6）
– 支持WLAN / WIFI以及移动数据最高为3G。 VpnCilla是不稳定的超过4G（LTE）在某些设备/与移动提供商
– 主动Screenfilter作为应用程序或黄昏力士可能会阻止选择安全对话框中的复选框
– VpnCilla不能处理阶段1密钥更新由VPN服务器发起的。在Fritzboxes这将occure后1小时的连接时间，而思科的VPN服务器的密钥更新间隔是可配置的，默认情况下8小时后。通常情况下，会话档2-3分钟，直到VpnCilla发起重新连接。